Fast turnaround cleaning
Ideal for spot treatment, touch-ups, and pre-wipe steps before coating, bonding, or assembly.
Product Industrial Cleaning
Solvent Spot Cleaner
Fast-evaporating spot cleaner for localized soil removal and pre-wipe steps — engineered for quick degreasing with minimal downtime and strong evaporation behavior.
Fast flash-off
Spot degreasing
Pre-wipe prep
Low-residue technique
Packaging: drums / IBC / bulk (as applicable)
Documentation: SDS / COA on request
Lead time depends on lane, packaging, and volume
Process-fit options
Different evaporation rates and solvency profiles available depending on soil type and substrate.
Procurement-ready
Quotes include packaging, Incoterms, lead time, and document pack scope for repeat orders.
Overview
Solvent spot cleaners are used where speed matters: they dissolve localized oils and organic soils, then evaporate quickly to support rapid return-to-service. This grade is typically used for spot degreasing, pre-wipe surface preparation, and touch-up cleaning where water-based cleaners are too slow or leave moisture.
Primary value
Rapid cleaning with controlled wet time for wipe-based workflows.
Typical placement
After bulk cleaning, before coating/bonding/assembly, or for localized rework.
Operational focus
Minimize downtime and reduce re-contamination with good wipe discipline.
Target soils
Oils, greases, handling residues, light adhesives, inks/markers (soil-dependent).
Target surfaces
Metals, many plastics, coated surfaces (always confirm compatibility with substrate).
When to use
Before painting/coating, bonding, gasket placement, assembly, or inspection wipe-down.
Typical industrial use cases
- Pre-wipe before coating, printing, labeling, or adhesive bonding
- Spot removal of oils and fingerprints on stainless and carbon steel parts
- Touch-up cleaning on maintenance shutdowns where drying time is limited
- Workshop and fabrication cleaning for localized contamination control
For heavy deposits, a staged approach (bulk degrease → rinse → solvent wipe) often reduces solvent usage and total cost.
Technical profile
A procurement-friendly technical summary. Confirm specifics on the quotation and SDS/COA pack.
| Parameter | Typical description | Why it matters |
|---|---|---|
| Cleaner type | Solvent-based spot cleaner (fast evaporating) | Supports rapid wipe cycles and minimizes downtime |
| Solvency focus | Optimized for organic soils (oil/ink/adhesive classes, soil-dependent) | Higher solvency reduces wipe passes and rework |
| Evaporation profile | Fast flash-off; alternative grades available for longer wet time | Match dry-time target to process window and soil load |
| Residue behavior | Low residue with correct wipe technique and compatible substrate | Critical for bonding/coating, inspection, and clean assembly steps |
| Application methods | Wipe / spray-wipe / spot treatment (process dependent) | Supports localized removal without full wash-down |
| Material compatibility | Metals typically compatible; plastics/elastomers/coatings must be tested | Avoids whitening, swelling, softening, or gloss loss |
| Safety & controls | May be flammable; requires ventilation, ignition control, PPE per SDS | Ensures safe handling and compliance with site controls |
| Documentation | SDS / COA on request; additional documents per destination | Enables onboarding, repeat procurement, and traceability |
Technical values and classification vary by grade and destination requirements. Request SDS/COA for your exact offer.
Wipe technique matters
Use clean lint-free wipes and rotate frequently to avoid re-depositing dissolved soils.
Compatibility checks
Test on plastics, elastomers, and coated surfaces to confirm no whitening, swelling, or softening.
Downstream integration
If used before bonding/coating, validate surface acceptance against your spec and QA checks.
Tip
If your main issue is adhesive residue, share the adhesive type (acrylic, rubber, silicone) so we can match solvency and wet time.
Typical specifications & formats
Values depend on grade and customer requirements. Confirm details on quotation.
Type
Solvent-based spot cleaner (fast evaporating)
Evaporation profile
Fast flash-off; alternative grades available for longer wet time
Use method
Wipe / spray-wipe / spot treatment (process dependent)
Residue profile
Low residue with correct technique; confirm for critical applications
Packaging
Drums / IBC (bulk as applicable)
Documentation
SDS / COA on request
Customization
Solvency and evaporation rate aligned to soil type and process constraints
Storage
Store sealed away from heat/ignition sources; follow SDS storage conditions
Traceability
Batch/lot traceability supported via COA where applicable
Specifications may vary by batch, origin, and packaging selection. For qualification, request SDS and a representative COA range.
Procurement, logistics & export readiness
We structure supply for repeat procurement: consistent grade definition, documentation pack, and export-ready packaging. Provide destination and volume to optimize landed cost and lane selection.
Packaging options
Drums and IBCs. Bulk options may be available depending on lane and destination.
Incoterms support
EXW / FOB / CFR / CIF structuring (as applicable) for planning and procurement clarity.
Document pack
SDS/COA standard. Additional documents available per project requirements.
Commercial details we include on the offer
- Grade/profile definition (evaporation / solvency fit)
- Packaging, palletization, and labeling scope
- Lead time by lane and requested volume
- Quote validity window and repeat-order parameters
- Documentation list (SDS/COA + destination needs)
What impacts lead time
- Grade (evaporation/solvency profile) and packaging selection
- Destination and any hazardous shipping constraints
- Documentation scope and labeling requirements
- Volume and frequency (spot vs recurring lane)
Commercial tip
If you need recurring supply, share a 3-month forecast window for better availability and stability.
FAQ
Quick answers for engineering, maintenance, and procurement teams.
Is it residue-free?
Designed for low-residue wiping with correct technique (clean wipes, frequent rotation). Residue acceptance depends on soil/substrate and downstream spec.
Can you provide slower/longer wet time?
Yes. Alternative evaporation profiles are available to increase wet time for heavier soils or larger wipe areas.
What documents can I request?
SDS and COA on request. Additional documentation and labeling support can be provided depending on destination and onboarding needs.
Qualification tip
If you need approval for bonding/coating, share the downstream process spec or acceptance criteria (e.g., “no visible residue”, “bond strength requirement”, “coating defect limit”).
Request a quotation
Send your requirements and we’ll respond with grade options, packaging, lead time, and documentation scope. For fastest turnaround, include soil type, substrate, and dry-time requirements.
Quote includes
Grade/profile • packaging • Incoterms • lead time • document pack • validity window
Lane routing
We route to the industrial cleaning lane for correct supplier and logistics alignment.
For trials
Ask about sample availability and a representative COA range (where available).
Prefer email? Send your RFQ to contact@atlastradehouse.com.